Products

Santam Technology research and development team through in-depth study, reveals more environmental factors when coupling protection repair material and concrete interface characteristics change law, put forward the complex construction environment guarantee durability regulation technology, innovation fully closed sequence grouting sealing hydraulic construction transverse joint leakage technology, develop bonding-buffer-wear-resistant multi-functional anti-resisting protection structure……

ST-TC400 water immune slow reaction two-component manual polyurea is a two-component, brush or rolling coating aliphatic polyurea elastic material. The product has the advantages of super weather resistance, excellent physical performance, high strength, good toughness and fast construction. The ST-TC400 is applied in outdoor engineering, and after 10 years of UV irradiation, the performance retention rate is still above 90%.

ST-P311 high performance fluorine silicon spraying polyurea, from group A polyisocyanate to polymer and B polyamine copolymer, through high temperature and high-pressure reaction injection molding equipment, by the metering pump to the spray gun, after rapid mixing, spray to the base surface, rapid reaction consolidation into elastic, tough special polymer coating, with waterproof, anti-corrosion, wear-resistant, seepage and crack resistance.

ST-PA410 fluorine silicon double component winter based on molecular structure control technology such as urea, in the winter resin molecular chain successfully implanted fluorine silicon molecular group, to deal with full water, strong ultraviolet (daily irradiation 20 MJ / m²), large temperature difference (extreme temperature difference nearly 80℃), high frequency freezing and melting (more than 200 times) environment, have excellent adaptability and weather resistance, is a complex harsh water environment concrete protection and repair ideal material selection.

ST-SC650 fluorosilicon single-component polyurea is a special polymer material in the aliphatic single component polyurea molecular chain, using polymer interpenetration network technology, grafting fluorosilicon molecular group, supplemented by nano-modified filler, to form a combination of rigid and soft, similar to the island structure of high strength and high wear resistance.

This product has the following characteristics:

1) has a good adhesion to a variety of film substrate, suitable for the composite of thick layer material, especially for some difficult to stick film substrate such as PVC, thick PE, has a better bonding effect;

2) Fast curing and short curing time can reduce the inventory quantity of ripening process products and form a fast cycle of finished products;

3) With better initial adhesion force, excellent stripping strength, suitable for the composite of rigid materials such as aluminum foil;

4) With good temperature resistance, and better adhesion and thermal sealing properties for the thick PE bottom membrane reinforced with multilayer structure;

5) High transparency, brightness, good film formation; good wetting and leveling performance, suitable for high and medium speed coating.

Santam ST-PG3000 has the following characteristics:

1) Health and environmental protection, zero formaldehyde, zero VOC

2) Excellent yellowing resistance

3) Mildew prevention, antibacterial, pollution resistance and easy to clean

This product has the following characteristics:

1) Good sealing performance, to block medium leakage;

2) Strong bonding, and closely combined with various materials;

3) Good weather resistance, adaptation to different climates;

4) Good elastic scalability, to adapt to size changes;

5) Waterproof and moisture-proof, to protect the objects;

6) Chemical corrosion resistance, good insulation;

7) Convenient construction, good environmental protection, strong customization;

This product has the following characteristics:

1) Good protection, block dust, moisture, etc.;

2) Excellent insulation to prevent short circuit leakage;

3) Good flexibility, can withstand stress and vibration;

4) High transparency, easy to observe the components;

5) Strong chemical stability, and chemical erosion resistance;

6) Good curing characteristics, fast curing, and easy to control;

7) Good thermal stability, to adapt to a certain temperature change;

This product has the following characteristics:

1) Good protection, block dust, moisture, etc.;

2) Excellent insulation to prevent short circuit and leakage;

3) Good flexibility, can withstand stress and vibration;

4) High transparency, easy to observe the components;

5) Strong chemical stability, and chemical erosion resistance;

6) Good curing characteristics, fast curing and easy to control;

7) Good thermal stability, to adapt to a certain temperature change;

The conductive adhesive has the following characteristics:

1. Excellent adhesion, good adhesion to various substrates
2. Good and stable conductivity
3. The drying time is fast and the operation is more efficient
4. One-component room temperature moisture curing, easy to use
5. Good resilience, excellent recovery performance for repeated compression deformation, and the usable compression rate is less than 35%.

Heat conductive adhesive is mainly used for heat conduction between different materials. That is, heat is transferred from high-temperature zone materials to low-temperature zone materials, so as to achieve heat dissipation effect and extend the service life of components. With the improvement of the processing capacity of electronic components and the development towards smaller and more compact electronic modules, the demand for heat dissipation is also increasing. Heat conductive materials can protect sensitive circuits and components in harsh environments reliably for a long time. ST-HC2533 is a high-strength and high-thermal-conductivity epoxy heat conductive adhesive.

Heat conductive adhesive is mainly used for heat conduction between different materials, that is, heat is transferred from high-temperature zone materials to low-temperature zone materials, so as to achieve heat dissipation effect and extend the service life of components. With the improvement of the processing capacity of electronic components and the development towards smaller and more compact electronic modules, the demand for heat dissipation is also increasing. Heat conductive materials can protect sensitive circuits and components in harsh environments for a long time and reliably. ST-HC 2511 is an epoxy heat conductive adhesive.

This product has the following characteristics:

1) It can replace the bolt components, simplify the structure, reduce the weight, and improve the energy of the battery pack per unit volume;

2) High fracture elongation and elastic modulus, high bonding strength, can withstand the disaster impact of 12m free fall and 120 km / h superimposed speed;

3) Flame retardant grade UL 94-VO, off the fire;

4) Excellent performance through the cold and heat cycle and heat and humidity aging test;

5) Excellent insulation performance and adjustable thermal conductivity parameters.

This product has the following characteristics:

1) It can replace the bolt components, simplify the structure, reduce the weight, and improve the energy of the battery pack per unit volume;

2) High fracture elongation and elastic modulus, high bonding strength, can withstand the disaster impact of 12m free fall and 120 km / h superimposed speed;

3) Flame retardant grade UL 94-VO, off the fire;

4) Excellent performance through the cold and heat cycle and damp and heat aging test;

5) Excellent insulation performance and adjustable thermal conductivity parameters.